This appendix summarizes technical specifications for the Origin Vault tower and rackmountable enclosure.
Table A-1 lists the various physical and environmental specifications that apply to the Origin Vault expansion option.
Table A-1. Origin Vault Specifications
Category | Tower | Rackmountable Enclosure |
|---|---|---|
Height | 22.4 inches (56.9 cm) | 6.8 inches (17.3 cm) |
Width | 7.5 inches (19 cm) without feet | 18.9 inches (22.6 cm) |
Length | 26 inches (66 cm) | 24.3 inches (61.7 cm) |
Weight |
|
|
Table A-2 lists (conservative) power specifications for the Origin Vault tower and rackmountable enclosure.
Table A-2. Origin Vault Power Specifications
Category | Value |
|---|---|
Power | Typically, 350 watts drawn from wall (460-watt power supply) |
Frequency | 50/60 Hz |
Voltage | 110/220 V for tower; 208-230 V for rackmountable at 50/60 Hz |
Inrush current | 140 amps maximum |
Cooling | 1,200 Btu/hr (0.1-ton AC load) maximum required |
Table A-3 lists operating environment conditions for the Origin Vault tower and rackmountable enclosure. For more detail on electrical and thermal issues, see Site Preparation for Origin Family, Onyx2, OCTANE, and O2.
Table A-3. Origin Vault Operating Environment Specifications
Category | Operating | Nonoperating |
|---|---|---|
Air temperature | < 5000 ft: 41° to 95° F (5° to 35° C) > 5000 ft: 41° to 86° F (5° to 30° C) | -4° to 140° F (0 to 60° C) |
Thermal gradient | 18° F (10° C)/ hour maximum | N/A |
Altitude | 10,000 ft (3,048 m) MSL, maximum | 40,000 ft (12,192 m) MSL, maximum |
Humidity | 10% - 90% (noncondensing) | 10% - 95% (noncondensing) |
Humidity gradient | 10% relative humidity/hour maximum | N/A |
Acoustics | 55 dBa | N/A |
Vibration | Maximum sustained: 5-10 Hz @ .01” total excursion, 10-500 Hz @ 0.1g Maximum peak: 5-10 Hz @ .01” total excursion, 10-500 Hz @ 0.1g Sensitive frequency: 8-33 Hz (varies with configuration) | N/A |
Table A-4 summarizes Origin Vault media.
Table A-4. Origin Vault Expansion Option Features
Feature | Configuration |
|---|---|
3.5-inch disk drives | Up to six, maximum height 1.6 inches (4 cm) Single-ended; differential with converter board With differential converter board, two connectors provided, allowing daisy-chaining; otherwise one connector only Termination: if two connectors (differential converter board) external termination required; if only one connector, terminated on backplane FAST-20 SCSI (40 megatransfers/sec) or SCSI-2; 16-bit wide |
5.25-inch drives | One full-height or two half-height, maximum height 1.6 inches (4 cm) Terminated on backplane; no daisy chaining Single-ended Fast-10 SCSI (20 megatransfers/sec) or SCSI-2 |
5.25-inch SCSI drive bay | Up to two drives, no daisy-chain option |
SCSI channels (internal) | One 68-wire single-ended, or two with differential converter board One single-ended, 50-wire |
SCSI channels (external) | Two 68-pin (FAST-20); three 68-pin with differential converter board |
Table A-5 gives 3.5-inch disk drive specifications.
Table A-5. Origin Vault Expansion Option 3.5-Inch Drives
Feature | 4.5 MB | 9.1 MB |
|---|---|---|
Connector | SCA-2 80-pin | SCA-2 80-pin |
Formatted capacity (MB) | 4,550 | 9,100 |
Heads/disks | 10/5 | 18/9 |
Track density (tpi) | 6,160 | 6,160 |
Average seek time (ms) | <9.5 | <10 |
Burst transfer rate (MB/sec) | 40 | 40 |
Buffer size (KB) | 256 | 256 |
Rotational speed (rpm) | 7,200 | 7,200 |
The external 68-pin SCSI connector on the rear of the Origin Vault chassis for the 3.5-inch drives supports both Ultra SCSI and SCSI-2 devices. It sends single-ended SCSI signals or differential signals, depending on the Origin Vault version. The external 68-pin SCSI connector for the 5.25-inch drives supports SCSI-2 devices only and sends single-ended signals only.
Table A-6 lists pinouts for the single-ended connection. In this table, the hyphen preceding a signal name indicates that the signal is low.
Table A-6. 68-Pin Single-Ended High-Density SCSI Pinouts
Signal Name | Pin Number | Pin Number | Signal Name |
|---|---|---|---|
Ground | 1 | 35 | -DB(12) |
Table A-7 lists pinouts for the differential connection. In this table, the hyphen preceding a signal name indicates that the signal is low.
Table A-7. 68-Pin Differential High-Density SCSI Pinouts
Signal Name | Pin Number | Pin Number | Signal Name |
|---|---|---|---|
+DB(12) | 1 | 35 | -DB(12) |