List of Figures

| Table of Contents | List of Figures | List of Tables |

Figure 1-1. Front View of the Workstation

Figure 1-2. Rear View of the Workstation

Figure 1-3. Connecting the K eyboard and Mouse Cables

Figure 1-4. Connecting the Ethernet Cable

Figure 1-5. Connecting the Monitor Cable

Figure 1-6. Connecting the Power Cable

Figure 1-7. Cabling a Dual-enclosure Workstation

Figure 1-8. Powering On the W orkstation

Figure 1-9. Login Screen

Figure 1-10. Peripheral Icons

Figure 1-11. Toolchest Menu

Figure 1-12. Console Window

Figure 1-13. System Shutdown Notifier

Figure 1-14. Power Button and Reset Button

Figure 1-15. Shutdown Caution Message

Figure 1-16. Shutdown System Window

Figure 1-17. System Shutdown Notifier

Figure 1-18. Restart Notifier

Figure 1-19. System Shutdown Notifier

Figure 1-20. Power Off/Restart Notifier

Figure 1-21. Restart Notifier

Figure 2-1. Single- and Dual-enclosure Rackmount Workstations

Figure 2-2. Front Panel Components

Figure 2-3. Rear Panel Components

Figure 2-4. System Architecture

Figure 2-5. DIMM Sockets and Pairs

Figure 2-6. Internal Hard Disk Drives and DVD-ROM Drive

Figure 2-7. Power Supply Location

Figure 3-1. Removing the Enclosure Cover

Figure 3-2. Installing the Enclosure Cover

Figure 3-3. PCI and PCI–X Card Slots Located in the Rear Panel

Figure 3-4. Removing the Lower PCI/PCI–X Support Bracket

Figure 3-5. Removing a Blanking Plate

Figure 3-6. Installing the Card and Retaining Screw

Figure 3-7. Replacing the Lower PCI/PCI–X Support Bracket

Figure 3-8. Removing the Lower PCI/PCI–X Support Bracket

Figure 3-9. Removing the Retaining Screw and Extracting the Card

Figure 3-10. Installing a Blanking Plate

Figure 3-11. Replacing the Lower PCI/PCI–X Support Bracket

Figure 3-12. Disk Drive Location

Figure 3-13. Installing a Disk Drive

Figure 3-14. Removing a Disk Drive

Figure 3-15. Layout of DIMM Slots and Local Memory Banks

Figure 3-16. Opening the Enclosure Cover to Install DIMMs

Figure 3-17. Removing the Plastic Air Baffle

Figure 3-18. Inserting a DIMM

Figure 3-19. Opening the Enclosure Cover to Remove DIMMs

Figure 3-20. Removing the Plastic Air Baffle

Figure 3-21. Removing a DIMM

Figure 3-22. L1 Controller Display on the Front Panel

Figure 3-23. Opening the Enclosure Cover to Access the L1 Controller Display

Figure 3-24. Removing the L1 Controller Display Panel

Figure 3-25. Installing an L1 Controller Display Panel

Figure 3-26. Power Supply Location

Figure 3-27. Removing the Power Supply

Figure 3-28. Installing the Power Supply

Figure 4-1. Full Support Sequence

Figure A-1. Rear Panel Connectors

Figure A-2. Ethernet 10/100/1000BaseT Port Pinout

Figure A-3. PS/2 Keyboard and Mouse Port Pinout

Figure A-4. Serial Port Pinouts and Locations

Figure A-5. External SCSI Port Pin Number Locations

Figure A-6. Stereo Jack Connector Conductors

Figure A-7. USB Type A Connector Pin Number Locations

Figure A-8. DVI-I Port Pinout and Location

Figure A-9. Stereo View Port Pinout

Figure A-10. Genlock Port Pinout

Figure A-11. Swap Ready Port Pinout

Figure B-1. Separating the Chassis Rail from the Slide Rail

Figure B-2. Attaching the Rear Mounting Bracket to the Slide Rail

Figure B-3. Attaching Chassis Rails to the Module Chassis

Figure B-4. Mounting Hole Pattern of Rack Vertical Rails

Figure B-5. Placing the Bar Nuts on the Rack Rails

Figure B-6. Attaching the Slide Rail to the Rack

Figure B-7. Installing Clip Nuts in Rack Rails

Figure B-8. Pressing the Safety Latches

Figure B-9. Securing the Module to the Rack

Figure B-10. Releasing the Safety Latches

Figure B-11. Releasing the Slide Latches

Figure D-1. Connecting a Monitor to the Workstation Expansion Enclosure

Figure D-2. USB Keyboard and Mouse Connected Directly to the Tezro Enclosure

Figure D-3. Second Keyboard and Mouse Connected via Optional USB Extender